[变频空调维修]-第5章-室内风机故障-第3节-室内风机内部霍尔元件损坏,室外机转一下就停

技术支持评论3,0532字数 3461阅读11分32秒阅读模式

空调培训资料缩略图

第3节 室内风机内部霍尔元件损坏,室外机转一下就停

故障说明

海信KFR-26GW/11BP挂式交流变频空调器在遥控开机后室外机运行一会就停机,室内风机一直高风运行。

1.查看故障代码

如图5-22左图所示,将空调器通上电源,遥控器开机后室内风机开始运行,主控继电器触点吸合向室外机输出交流220V,约4s后压缩机运行,7s后室外风机运行,12s后室内机主板主控继电器触点断开,停止向室外机供电,压缩机和室外风机停止运行,约3min后室内机主板主控继电器触点吸合后马上就断开。

查看室内风机一直为超高风运行,测量绕组供电插座电压为交流220V,和供电电压相同,按压遥控器“风速”按键调至“低风”,室内风机仍然以超高风运行。

如图5-22右图所示,按压遥控器“传感器切换”键2次,调出故障代码,室内机显示板组件“定时”灯亮,查看代码含义为“室内风机故障”,说明室内机CPU检测不到室内风机输出的霍尔反馈信号。由于室内风机可以运行,因此应检查霍尔反馈插座电压。

图5-22 室外机运行一会就停机和室内机显示板组件故障代码

图5-22 室外机运行一会就停机和室内机显示板组件故障代码

2.测量霍尔反馈插座电压

如图5-23左图所示,在室内风机运行时,使用万用表直流电压挡,将黑表笔接霍尔反馈插座中黄色引线即直流地,红表笔接棕色引线即测量霍尔反馈供电电压,正常为直流5V,实测电压说明供电电压正常。

如图5-23右图所示,黑表笔不动(接直流地),红表笔接黑色引线测量霍尔反馈信号,正常为供电电压一半,即直流2.5V左右,实测电压为直流1.5V,与正常值相差较多,判断霍尔反馈电路出现故障。

图5-23 测量霍尔反馈插座供电电压和反馈电压

图5-23 测量霍尔反馈插座供电电压和反馈电压

3.拨动贯流风扇测量霍尔反馈电压

按压遥控器“开/关”按键关闭空调器,但不拔下电源插头即处于待机状态下。如图5-24所示,手从出风框处伸入慢慢拨动贯流风扇,PG电机中的转子也慢慢转动,同时使用万用表直流电压挡测量霍尔反馈电压,正常应为跳动电压,即0V—5V—0V—5V变化,而实测电压为稳压不变的直流1.5V,判断PG电机内部霍尔损坏。

图5-24 用手拔动贯流风扇时测量霍尔反馈电压

图5-24 用手拔动贯流风扇时测量霍尔反馈电压

4.霍尔元件

拔下空调器电源插头,取下电控盒和蒸发器,在取下PG电机盖板后,松开PG电机轴与贯流风扇的固定螺丝,即可抽出PG电机,观察霍尔反馈引线由下盖处引出,说明霍尔元件电路板位于电机的下部,使用平口螺丝刀轻轻撬开下盖,如图5-25所示,即可看见电路板,霍尔元件与转子上磁环相对应,取下电路板后,可见电路板组成也很简单,由霍尔元件、3个电阻、1个电容组成,电路原理图如图5-26所示。

图5-25 霍尔元件、磁环安装位置和电路板

图5-25 霍尔元件、磁环安装位置和电路板

图5-26 海信KFR-26GW/11BP霍尔电路原理图

图5-26 海信KFR-26GW/11BP霍尔电路原理图

如图5-27所示,电路板上为防止霍尔元件移动,使用一个塑料框用于固定,使用烙铁焊下霍尔元件,其型号为40AF,外观和三极管类似。它共有3个引脚,①脚为供电(VCC),接直流5V;②脚为GND,接直流电源地;③脚为输出端(VOUT)。

图5-27 霍尔元件在电路板的安装位置和40AF实物外观

图5-27 霍尔元件在电路板的安装位置和40AF实物外观

维修措施

如图5-28所示,更换霍尔元件。由于没有相同型号的霍尔元件更换,使用外观与引脚功能均相同的44E代换。

图5-28 更换44E霍尔元件

图5-28 更换44E霍尔元件

剪去多余的引脚后安装霍尔元件电路板,组装好拆下的PG电机,并将PG电机安装在室内机底座上面,安装PG电机盖板、蒸发器、电控盒,恢复连接引线后将空调器通上电源但不开机即处于待机状态下。如图5-29所示,手从出风框处伸入慢慢拨动贯流风扇,同时使用万用表直流电压挡测量霍尔反馈插座中输出引线(黑线)和地电压,实测为0.3V—5V—0.3V—5V跳动变化。遥控开机,室内风机运行,测量霍尔反馈电压为稳定的直流2.7V,且室内风机转速随遥控器上风速控制变换,低风时线圈电压约为交流120V。室内机主板向室外机供电后,压缩机和室外风机一直运行不再停机,制冷恢复正常,故障排除。

图5-29 测量霍尔反馈插座反馈电压

图5-29 测量霍尔反馈插座反馈电压

总结

①霍尔元件工作原理。霍尔元件是一种基于霍尔效应的磁传感器,用它可以检测磁场及其变化,可在各种与磁场有关的场合中使用。应用在PG电机中时,霍尔元件安装在电路板上,电机的转子上面安装有磁环,在空间位置上霍尔元件与磁环相对应,转子旋转时带动磁环转动,霍尔元件将磁感应信号转化为高电平或低电平的脉冲电压由输出脚输出,至主板CPU,CPU根据脉冲电压计算出电机的实际转速,与目标转速相比较,如有误差则改变光耦可控硅的导通角,从而改变PG电机的转速,使之与目标转速相对应。

②电路板固定方式。如图5-30所示,霍尔元件电路板安装在PG电机内部,根据电机型号不同,安装的位置也不一样,有些安装在电机上部,因此霍尔反馈引线从上部伸出;有些安装在电机下部,引线从下部伸出。

图5-30 霍尔元件电路板安装位置

图5-30 霍尔元件电路板安装位置

在拆卸电机前应注意霍尔元件电路板的安装位置,因为PG电机外壳通常为高强度的塑料制成,并且有些电机只能从一侧打开,如果没有仔细观察就开始强拆,就会造成PG电机外壳被破坏或转子移动时顶坏霍尔元件电路板,这时电机只能报废。

③霍尔元件固定方式。本机霍尔元件由一个塑料框固定,在更换时其位置不会改变,如果某些型号的霍尔元件电路板不带固定的塑料框,如图5-31所示,在安装时应将霍尔元件尽量靠前和竖直。在实际维修过程中,如果安装霍尔元件时向后靠约0.5cm,便不能接收PG电机转子磁场感应信号,输出端电压一直为直流5V或0V,安装开机后CPU同样检测不到霍尔反馈信号。

图5-31 霍尔元件安装方法

图5-31 霍尔元件安装方法

④霍尔元件电路板12V供电。霍尔元件供电电压通常为直流5V,在空调器通上电源但不开机即待机状态下,用手拨动贯流风扇时输出端为0V—5V—0V—5V跳动变化的电压,电机运行时约为供电电压的一半,即2.5V。

如图5-32所示,美的空调器霍尔元件电路板供电通常为直流12V,待机状态下用手拨动贯流风扇时,输出端电压为0V—7.6V—0V—7.6V跳动变化,电机运行时输出端电压约为4V。

图5-32 测量直流12V供电的霍尔反馈电压

图5-32 测量直流12V供电的霍尔反馈电压

⑤霍尔反馈插头引线辨认方法。如图5-33所示,判断主板插座引针功能的方法是,查看引针与7805稳压块的引脚相通情况,与7805②脚(地)相通的引针为地,与7805③脚(5V)相通的引针为5V,最后一个引针去CPU引脚,为反馈端。

判断PG电机反馈插头引线功能的方法是,将插头插进插座,根据引针的功能即可判断出引线的功能。

图5-33 霍尔反馈插座引针功能判断方法

图5-33 霍尔反馈插座引针功能判断方法


Warning: file_exists(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/2024/03) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2036

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/2024) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 7

Warning: file_exists(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2036

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_file(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c96.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 21

Warning: is_file(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 22

Warning: fopen(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 26

Warning: fopen(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png): Failed to open stream: Operation not permitted in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 26

Fatal error: Uncaught TypeError: fclose(): Argument #1 ($stream) must be of type resource, bool given in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php:27 Stack trace: #0 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php(27): fclose() #1 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/template/copyright.php(21): begin_avatar() #2 /www/wwwroot/yxjdzl.com/wp-includes/template.php(772): require('...') #3 /www/wwwroot/yxjdzl.com/wp-includes/template.php(716): load_template() #4 /www/wwwroot/yxjdzl.com/wp-includes/general-template.php(204): locate_template() #5 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/single-default.php(16): get_template_part() #6 /www/wwwroot/yxjdzl.com/wp-includes/template.php(772): require('...') #7 /www/wwwroot/yxjdzl.com/wp-includes/template.php(716): load_template() #8 /www/wwwroot/yxjdzl.com/wp-includes/general-template.php(204): locate_template() #9 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/single.php(6): get_template_part() #10 /www/wwwroot/yxjdzl.com/wp-includes/template-loader.php(106): include('...') #11 /www/wwwroot/yxjdzl.com/wp-blog-header.php(19): require_once('...') #12 /www/wwwroot/yxjdzl.com/index.php(17): require('...') #13 {main} thrown in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 27
WordPress › 错误