[变频空调维修]-第2章-制冷效果差故障-第5节-轴承卡死,室外风机不运行

技术支持评论1,483字数 2448阅读8分9秒阅读模式

空调培训资料缩略图

第5节 轴承卡死,室外风机不运行

故障说明

海信KFR-26GW/11BP挂式交流变频空调器遥控开机后室内机主板向室外机供电,室内机显示板组件“运行”灯亮,说明压缩机已开始运行,室内机也开始吹凉风,但吹风温度逐渐上升,约5min后室内机吹风为热风,然后逐渐变为自然风,“运行”指示灯熄灭,表示压缩机已停止运行。

1.检查室外风机

如图2-19所示,拔下空调器电源,待约3min后重新上电,遥控开机后到室外机处检查,压缩机运行,但室外风机不运行,手摸冷凝器烫手,压缩机运行频率也逐渐下降。由于室外风机不运行,冷凝器过热,压缩机容易过热损坏。断开空调器电源,拔下室外机模块板上的压缩机的3根引线,再次上电开机,室外风机和压缩机均不运行。使用万用表交流电压挡测量室外风机供电,实测电压为交流220V,说明室外机主板供电正常。

图2-19 室外风机不运行和测量供电电压

图2-19 室外风机不运行和测量供电电压

2.测量室外风机进行电流

使用万用表交流电流挡,如图2-20左图所示,测量室外风机公共端白色引线电流约为0.4A,可说明室外机主板已输出供电,且室外风机公共端C与运行绕组R的线圈阻值正常,否则电流为0A。

室外风机得到供电后仍不运行,原因有2个,一个是轴承卡死,另一个是启动电容损坏。为判断故障,用手拨动室外风机扇叶,感觉很沉重,室外风机仍不运行,判断轴承卡死。因为启动电容损坏引起的室外风机不运行时,如果用手拨扇叶,相当于增加启动力矩,室外风机应能运行起来。断开空调器电源,再用手拨动室外风机扇叶仍然拨不动,如图2-20右图所示,确定室外风机内部轴承卡死,维修时可更换轴承处理。

图2-20 测量室外风机运行电流和用手转动扇叶

图2-20 测量室外风机运行电流和用手转动扇叶

3.测量室外风机绕组线圈阻值

使用万用表电阻挡测量室外风机绕组线圈阻值,如果线圈开路或短路损坏,再更换轴承已经没有意义,因此在更换前应确定室外风机绕组线圈阻值是否正常,如图2-21所示,实测公共端C与运行绕组R阻值为203Ω,公共端C与启动绕组S阻值为241Ω,运行绕组R与启动绕组S阻值为444Ω,说明室外风机绕组线圈阻值正常。

图2-21 测量室外风机绕组线圈阻值

图2-21 测量室外风机绕组线圈阻值

4.室外风机

室外风机的实物外观如图2-22所示。由于使用塑封电机,即绕组定子、外壳、下盖使用高强度塑料封装为一体,和室内风机类似,因此结构较为简单,主要由定子、转子、上盖组成。

图2-22 室外风机外观和内部结构

图2-22 室外风机外观和内部结构

取出转子,用手转动上轴承和下轴承,发现下轴承阻力较大,如果不使劲还真转不动,判断为下轴承损坏,轴承型号为608Z(见图2-23)。但考虑到下轴承损坏时一般上轴承也将严重磨损,因此将上下两个轴承一块更换。

图2-23 更换轴承

图2-23 更换轴承

维修措施

如图2-24所示,更换室外风机转子的上下2个轴承,更换后组装室外风机,用手转动转轴感觉很轻松,将室外风机安装在室外机上面,安装线圈插头和压缩机的3根引线,再次上电开机,压缩机运行后,室外风机也开始运行,并且转速正常,运行时噪声也不大,在出风框处感觉出风量很大,制冷恢复正常,故障排除。

图2-24 更换轴承后用手转动转轴

图2-24 更换轴承后用手转动转轴

总结

①电机轴承的滚珠卡死引起室外风机或室内风机不运行,在实际维修中故障率不是很高,但由于轴承缺油引起的噪声大故障则比较常见。

②本机室外风机使用塑封包装,定子、绕组、外壳等固定为一体。在实际应用中,常见还有普通封装方式(见图2-25),由上盖、下盖、定子(包括绕组)、转子(包括轴承)组成。

图2-25 普通封装室外风机内部结构

图2-25 普通封装室外风机内部结构

③在检修空调器时,通常需要拆下室外机外壳,而在更换故障元器件或在检修过程中试机时,通常在室外机外壳不安装的情况下开机运行,但由于未安装室外机外壳,室外机的轴流风扇不能对冷凝器有效散热,表现出制冷效果差的故障。以检修海信KFR-60LW/BP柜式交流变频空调器为例,维修内容为更换室外风机。

未安装室外机外壳试机:如图2-26左图所示,室外机运行一段时间后,压缩机以低频运行,整机运行电流6A,系统运行压力0.75MPa,室内机不显示故障代码,制冷效果极差,室内机出风框只有一格为凉风,其他几格为自然风,手摸冷凝器烫手,原因为室外机外壳未安装时,室外风机不能为冷凝器有效散热,压缩机排气温度过高,室外机主板CPU检测后控制压缩机低频运行。

图2-26 未安装室外机外壳和安装室外机外壳

图2-26 未安装室外机外壳和安装室外机外壳

安装室外机外壳后试机:如图2-26右图所示,室外机运行一段时间后,压缩机以高频运行,整机运行电流为12A,系统运行压力为0.45MPa,室内机出风框从下到上都是凉风,制冷恢复正常。

从本例可以看出,在检修空调器试机时应安装室外机外壳,如果不方便安装,至少要将室外机顶盖放在冷凝器上面,这样也能达到为冷凝器散热的效果。


Warning: file_exists(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/2024/03) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2036

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/2024) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 7

Warning: file_exists(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2036

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_file(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c96.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 21

Warning: is_file(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 22

Warning: fopen(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 26

Warning: fopen(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png): failed to open stream: Operation not permitted in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 26

Warning: fclose() expects parameter 1 to be resource, bool given in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 27
管理员
  • 本文由 发表于 2018年4月9日 19:53:15
  • 除非特殊声明,本站文章均为原创,转载请务必保留本文链接
自制美的变频空调检测仪二代 硬件开发

自制美的变频空调检测仪二代

检测仪简介 256*160大分辨率,适配外壳为125mm*80mm*32mm 支持5V i2c检测口和LNS检测口,修板子除通讯故障外均建议用i2c接口 自动判断当前插入的接口(5V i2c还是LNS...
自制 美的专区

自制”美的变频空调检测仪”教程

2021年4月14日更新 说明   本人不卖硬件、不卖成品、和硬件商家无任何关系、非美的厂家人员,这个教程主要是为了方便广大维修工,本人是业余独立开发者,bug避免不了,但我会持续不定时更新,不断完善...
匿名

发表评论

匿名网友 填写信息

:?: :razz: :sad: :evil: :!: :smile: :oops: :grin: :eek: :shock: :???: :cool: :lol: :mad: :twisted: :roll: :wink: :idea: :arrow: :neutral: :cry: :mrgreen:

确定