[变频空调维修]-第7章-室外机强电通路故障-第1节-滤波板线圈开路,室外机不运行

技术支持评论1,958字数 3285阅读10分57秒阅读模式

空调培训资料缩略图

第1节 滤波板线圈开路,室外机不运行

故障说明

海信KFR-4001GW/BP挂式交流变频空调器制冷开机后室内风机运行但室外机不运行,室内机显示屏频率条只有1格亮,2min后频率条熄灭,此时按压“应急开关”按键约5s,蜂鸣器响2声,显示故障代码为“5”,含义为“通信故障”。图7-1所示为室外机直流300V电压产生电路原理图。

图7-1 海信KFR-4001GW/BP直流300V电压产生电路原理图

图7-1 海信KFR-4001GW/BP直流300V电压产生电路原理图

1.测量室内机供电电压和通信电路电压

掀开室内机进风格栅,取下接线端子盖螺丝,室内外机的接线端子共有4根引线,1号为L端子,2号为N端子,3号为地线,4号为SI端子。其中1和2端子组合为交流220V电压,为室外机供电;2和4组合为直流24V以内的跳变电压,为室内机和室外机主板上的通信电路提供回路。

如图7-2左图所示,使用万用表交流电压挡,测量接线端子上1号和2号端子电压,实测电压为交流220V,说明室内机主板已输出电压为室外机供电。

如图7-2右图所示,万用表改用直流电压挡,黑表笔接2号N端子,红表笔接4号SI端子,正常为直流0V—24V跳动变化的电压,而实测为直流23V左右跳动变化的电压,初步判断室外机CPU没有工作或室外机没有供电。

图7-2 测量室内机接线端子交流电压和通信电压

图7-2 测量室内机接线端子交流电压和通信电压

2.测量室外机供电和室外机主要元器件设计位置

如图7-3左图所示,使用万用表交流电压挡,在室外机接线端子处测量1号和2号端子电压,实测结果为交流220V,说明室内机主板输出的供电已送至室外机。

图7-3右图所示为室外机主要元器件设计位置。

图7-3 测量室外机接线端子交流电压及主要元器件位置

图7-3 测量室外机接线端子交流电压及主要元器件位置

3.测量直流300V电压和硅桥输入端电压

室外机CPU工作电压为直流5V,由开关电源提供,而开关电源的工作电压为直流300V,取自室外机主滤波电容,因此使用万用表直流电压挡,如图7-4左图所示,测量直流300V电压,红表笔接主滤波电容正极、黑表笔接负极(相当于测量图7-1的P、N位置电压),正常值为直流300V,而实测电压为直流0V。

直流300V电压为0V的故障原因有:①后级负载(即模块P、N端子)短路,使得交流电源为主滤波电容充电时,PTC电阻发热,阻值变为无穷大;②滤波电感线圈开路,使得硅桥输出的直流300V电压未送至主滤波电容;③硅桥损坏,在输入端交流220V电压正常的前提下,未输出直流300V电压;④PTC电阻开路损坏,使得交流220V电压未送至硅桥交流输入端;⑤交流供电回路开路,使得交流220V电压不能送至硅桥交流输入端。

如图7-4右图所示,万用表改为交流电压挡,表笔接硅桥的2个交流输入端子(相当于测量图7-1的E、F位置电压),正常电压为交流220V,实测电压为交流0V,排除故障原因中的②和③,应测量室外机主板的交流输入端电压。

图7-4 测量直流300V电压和硅桥输入端电压

图7-4 测量直流300V电压和硅桥输入端电压

4.测量室外机主板输入端电压和滤波板输入端电压

如图7-5左图所示,依旧使用万用表交流电压挡,测量室外机主板交流输入端电压(相当于测量图7-1的C、D位置电压),正常电压为交流220V,而实测电压为交流0V,说明交流电源未送至室外机主板,可排除故障原因中的①和④,应向前级检查。

由于室外机主板的交流电源由滤波板输出端直接提供,因此使用万用表交流电压挡,如图7-5右图所示,测量滤波板输入端电压(相当于测量图7-1的A、B位置电压),正常电压为交流220V,实测电压说明正常,可判断故障点在滤波板。

图7-5 测量室外机主板输入端电压和滤波板输入端电压

图7-5 测量室外机主板输入端电压和滤波板输入端电压

5.测量滤波板输入端和输出端引线阻值

断开空调器电源,使用万用表电阻挡测量滤波板输入端与输出端的引线阻值,如图7-6所示。首先测量电源L线阻值(相当于测量图7-1的A、C位置),实测阻值为0Ω,说明L线正常;然后测量电源N线阻值(相当于测量图7-1的B、D位置),正常值为0Ω,实测结果为无穷大,说明电源N线开路。

图7-6 测量滤波板输入端和输出端引线阻值

图7-6 测量滤波板输入端和输出端引线阻值

说明:此处为使图片显示清晰,将滤波板拆下单独测量,实际维修过程中不用拆下,直接在路测量即可。

6.查看滤波板线圈焊点

如图7-7所示,翻过滤波板,查看焊点的一面,发现滤波线圈4个焊点的其中1个铜箔烧穿损坏(本例对应图7-1中的D位置),使得电源N线开路,交流220V电压无法送至硅桥的交流输入端,室外机无直流300V电压,开关电源不能工作,无直流5V电压输出,CPU因无工作电压也不能工作,通信电路中断,室内机CPU检测后判断为通信故障,约 2min后停止室外机供电。

图7-7 滤波板线圈焊点开焊

图7-7 滤波板线圈焊点开焊

维修措施

更换滤波板。再次上电开机,室内机显示屏频率条亮度一直上升,室外风机和压缩机开始工作,空调器开始制冷,使用万用表直流电压挡,测量接线端子2 号N端和4号SI端电压,为正常的0V—24V跳变电压。

应急措施

如果暂时没有相同型号的滤波板更换,有2种应急措施。

①将滤波板重新开孔,并刮净表面绝缘层,再将滤波线圈引线表面刮净,并穿入新开的滤波板焊孔,使用烙铁将焊点焊好即可。

②本例为滤波板上电源N线开路,可在根部剪断滤波板的输入端和输出端引线,将接线端子上引线和室外机主板的输入引线(相当于图7-1的B、D位置)直接相连,作用是短接滤波板,这样上电开机后室外机同样可以正常工作。

知识链接

滤波板

①海信早期交流变频空调器机型如KFRP-35GW、KFRP-40GW,完全使用三洋技术的生产线,在实际维修中经常发生与本例相同的故障,即滤波板线圈焊点烧穿损坏(或焊点虚

CPU传送的通信信号,马上就会停止室外机的供电。即在实际维修中,使用万用表交流电压挡,测量室内机接线端子L、N的交流220V电压,只显示约5s的时间就变为0V了,而本例机型(海信KFR-4001GW/BP)如室内机CPU检测不到室外机CPU传送的通信信号,则2min后才会停止向室外机的供电。

②海信中期部分机型如KFR-26GW/11BP,室外机交流供电电路不再使用滤波板,而是使用滤波器,安装位置及实物外观如图7-8所示。其将滤波线圈和电容集成在一个铁壳内,如果内部的滤波线圈开路损坏,同样出现如本例的故障。滤波器输入端接图7-1中的A、B位置,输出端接C、D位置。

图7-8 滤波器安装位置及实物外观

图7-8 滤波器安装位置及实物外观

③滤波板具有双向作用,既能吸收电网中的谐波,防止对电控系统的干扰,又能防止电控系统的谐波进入电网。目前的变频空调器室外机通常不再使用滤波板或滤波器,而是使用PFC电路(即功率因数校正电路)代替,实物外观如图7-9所示。

图7-9 PFC电路板

图7-9 PFC电路板


Warning: file_exists(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/2024/03) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2036

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/2024) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 7

Warning: file_exists(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2036

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_file(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c96.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 21

Warning: is_file(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 22

Warning: fopen(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 26

Warning: fopen(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png): Failed to open stream: Operation not permitted in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 26

Fatal error: Uncaught TypeError: fclose(): Argument #1 ($stream) must be of type resource, bool given in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php:27 Stack trace: #0 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php(27): fclose() #1 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/template/copyright.php(21): begin_avatar() #2 /www/wwwroot/yxjdzl.com/wp-includes/template.php(772): require('...') #3 /www/wwwroot/yxjdzl.com/wp-includes/template.php(716): load_template() #4 /www/wwwroot/yxjdzl.com/wp-includes/general-template.php(204): locate_template() #5 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/single-default.php(16): get_template_part() #6 /www/wwwroot/yxjdzl.com/wp-includes/template.php(772): require('...') #7 /www/wwwroot/yxjdzl.com/wp-includes/template.php(716): load_template() #8 /www/wwwroot/yxjdzl.com/wp-includes/general-template.php(204): locate_template() #9 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/single.php(6): get_template_part() #10 /www/wwwroot/yxjdzl.com/wp-includes/template-loader.php(106): include('...') #11 /www/wwwroot/yxjdzl.com/wp-blog-header.php(19): require_once('...') #12 /www/wwwroot/yxjdzl.com/index.php(17): require('...') #13 {main} thrown in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 27
WordPress › 错误