[格力空调维修] 第3章-常见电路故障-第1节-上电无反应故障

技术支持评论3,107字数 3731阅读12分26秒阅读模式

第1节 上电无反应故障

上电无反应故障表现现象为将空调器通上电源,上电复位时整机无任何反应,蜂鸣器不响、指示灯和显示屏均不亮,使用遥控器和应急开关按键均不能开机。常见故障部位为电源电路,本节将重点介绍。

一、电源电路工作原理

电源电路原理图见图3-1,实物图见图3-2,关键点电压见表3-1。电源电路的作用是将交流220V电压经降压、整流、滤波、稳压后转换为直流12V和5V为主板供电。

电容C143为高频旁路电容,用以旁路电源引入的高频干扰信号;FU101(3.15A保险管)、RV101(压敏电阻)组成过压保护电路。当输入电压正常时,对电路没有影响;而当电压高于交流约380V,RV101迅速击穿,将前端FU101保险管熔断,从而保护主板后级电路免受损坏。

变压器、D1~D4(整流二极管)、D176、E3(主滤波电容)、C16、C17组成降压、整流、滤波电路。变压器将输入电压交流220V降低至约交流12V从二次绕组输出,至由D1~D4组成的桥式整流电路,变为脉动直流电(其中含有交流成分),经D176再次整流、E3滤波,滤除其中的交流成分,成为纯净的约12V直流电压,为主板12V负载供电。

本电路没有使用7812稳压块,直流12V电压实测为11~16V,并且随输入的交流220V电压变化而变化。

V172、C4、C18组成5V电压产生电路。V172(7805)为5V稳压块,①脚输入端为直流12V,经7805内部电路稳压,③脚输出端输出稳定的直流5V电压,为5V负载供电。

表3-1 电源电路关键点电压

表3-1 电源电路关键点电压

图3-1 电源电路原理图

图3-1 电源电路原理图

图3-2 电源电路实物图

图3-2 电源电路实物图

二、检修流程

1.将导风板扳到中间位置

拔下空调器电源插头,用手将上下导风板扳到中间位置,见图3-3。再为空调器通上电源,观察导风板状态以区分故障。

空调器正常时导风板应能自动关闭,此时可说明室内机主板直流5V电压正常且CPU工作正常,所表现的上电无反应故障可能为不接收遥控信号故障。

重新上电后导风板位置保持不变,说明空调器有故障,应进入第2检修步骤。

图3-3 扳动导风板至中间位置

图3-3 扳动导风板至中间位置

2.测量插座电压

使用万用表交流电压挡,见图3-4。测量为空调器供电的电源插座电压。

如实测电压为交流220V,说明供电正常,故障在室内机,进入第3检修步骤。

如实测电压为交流0V,说明空调器供电线路有故障,应检查电源插座或空气开关处电压等。

图3-4 测量插座电压

图3-4 测量插座电压

3.测量电源插头阻值

使用万用表电阻挡,见图3-5。测量电源插头L-N阻值以区分故障。

如实测阻值为变压器一次绕组阻值约500Ω,说明变压器一次绕组回路正常,进入第6检修步骤。

如实测阻值为无穷大,说明变压器一次绕组回路有开路故障,进入第4检修步骤,重点检查变压器一次绕组、保险管等。

图3-5 测量电源插头阻值

图3-5 测量电源插头阻值

4.测量保险管阻值

断开空调器电源,使用万用表电阻挡测量,见图2-9。

如实测阻值为0W,说明保险管正常,应进入第5检修步骤。

如实测阻值为无穷大,说明保险管开路损坏,检查损坏原因后更换保险管。

5.测量变压器一次绕组阻值

使用万用表电阻挡测量,见图2-3。

如实测阻值约500Ω,说明变压器一次绕组正常,应检查故障是否由于一次绕组插头与插座接触不良引起。

如实测阻值为无穷大,说明一次绕组开路损坏,应更换变压器。

图2-9中实测变压器为柜式空调器上所使用,其阻值较小约200Ω。

6.测量7805输出端5V电压

将空调器通上电源,使用万用表直流电压挡,黑表笔接7805的②脚地、红表笔接③脚输出端测量电压,见图2-19。

如实测电压为直流5V,说明电源电路正常,故障可能为CPU死机或其他弱电电路损坏,检查故障原因或更换室内机主板试机。

如实测电压为直流0V,说明电源电路有故障,应进入第7检修步骤。

7.测量7805输入端12V电压

依旧使用万用表直流电压挡,黑表笔不动依旧接地、红表笔接7805的①脚输入端测量电压,见图2-18。

如实测电压约为直流14V,排除5V负载短路故障,直流5V电压为0V的原因是7805损坏,应更换7805。

如实测电压为直流0V,说明变压器二次绕组整流滤波电路有故障,应进入第8检修步骤。

8.测量变压器二次绕组插座电压

测量变压器二次绕组插座电压见图2-6。使用万用表交流电压挡,测量变压器二次绕组插座电压。

如实测电压约交流12V,说明为整流滤波电路故障,如排除直流12V负载短路故障,为整流二极管或滤波电容损坏,可更换元件或室内机主板。

如实测电压为交流0V,排除整流二极管短路故障,应进入第9检修步骤。

9.测量变压器一次绕组插座电压

测量变压器一次绕组插座电压见图2-5。使用万用表交流电压挡,测量一次绕组插座电压,实测电压应为交流220V(前提是电源电压和测量插头L-N阻值均正常),可说明变压器损坏,应更换变压器。

三、维修实例—变压器一次绕组开路

说明:KFR-23GW/(23570)Aa-3空调器,用户反映上电无反应。

1.测量电源插头L-N阻值

将导风板扳到中间位置,再将空调器插头插入电源,上电后导风板不能自动复位,判断空调器或电源插座有故障,见图3-6(a)。

使用万用表交流电压挡,测量电源插座电压为交流220V,说明电源供电正常,故障在空调器。使用万用表电阻挡,测量电源插头L-N阻值,实测为无穷大,而正常值约500Ω,确定故障在室内机,见图3-6(b)。

2.测量保险管和一次绕组阻值

使用万用表电阻挡,测量3.15A保险管FU101阻值为0Ω,说明保险管正常,见图3-7。测量变压器一次绕组阻值,实测为无穷大,说明变压器一次绕组开路损坏。

维修措施:更换变压器,见图3-8。更换后上电试机,将电源插头插入电源,蜂鸣器响一声后导风板自动关闭,使用遥控器开启,空调器制冷恢复正常。

图3-6 扳动导风板和测量电源插头阻值

图3-6 扳动导风板和测量电源插头阻值

图3-7 测量保险管和一次绕组阻值

图3-7 测量保险管和一次绕组阻值

图3-8 更换变压器

图3-8 更换变压器

四、维修实例—CPU死机

故障说明:某型号挂式空调器,用户报修上电无反应。

1.按压应急开关按键

上门检查,见图3-9。将空调器通上电源,导风板不能自动关闭,蜂鸣器不响,显示板组件上显示屏和指示灯均不亮;掀开进风格栅,使用万用表表笔按压应急开关按键(AUTO)也无反应,初步判断主板电源电路未工作或CPU未工作。

使用万用表交流电压挡测量电源插座交流220V电压正常,使用万用表电阻挡测量电源插头L-N阻值正常,说明变压器一次绕组回路正常。

图3-9 按压应急开关按键

图3-9 按压应急开关按键

2.测量5V电压和晶振电压

取下室内机外壳,使用万用表直流电压挡,测量7805输出端直流5V电压正常,说明电源电路工作正常,见图3-10(a)。

依旧使用万用表直流电压挡,检查CPU三要素电路。直流5V电压已检查为正常,见图3-10(b)。测量晶振电压,黑表笔接晶振中间引脚地,红表笔测量两侧引脚,实测电压分别为2.3V和2.4V,说明晶振电路正常;测量复位三极管Q1发射极电压为直流5V,说明复位电路正常。

维修措施:由于CPU三要素电路正常,而CPU不能工作,判断CPU死机或相关弱电电路故障,由于无法修复,实际维修时,更换室内机主板,见图3-11,更换后试机正常。

图3-10 测量5V和晶振电压

图3-10 测量5V和晶振电压

图3-11 更换主板

图3-11 更换主板


Warning: file_exists(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/2024/03) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2036

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/2024) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 7

Warning: file_exists(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2036

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www/wwwroot) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/www) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_dir(): open_basedir restriction in effect. File(/) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-includes/functions.php on line 2047

Warning: is_file(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c96.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 21

Warning: is_file(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 22

Warning: fopen(): open_basedir restriction in effect. File(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png) is not within the allowed path(s): (/www/wwwroot/yxjdzl.com/:/tmp/) in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 26

Warning: fopen(/www/wwwroot/www.yxjdzl.com/wp-content/uploads/avatar/b32f9e95aaf5f958e5327dc1538e4e1c-d.png): Failed to open stream: Operation not permitted in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 26

Fatal error: Uncaught TypeError: fclose(): Argument #1 ($stream) must be of type resource, bool given in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php:27 Stack trace: #0 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php(27): fclose() #1 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/template/copyright.php(21): begin_avatar() #2 /www/wwwroot/yxjdzl.com/wp-includes/template.php(772): require('...') #3 /www/wwwroot/yxjdzl.com/wp-includes/template.php(716): load_template() #4 /www/wwwroot/yxjdzl.com/wp-includes/general-template.php(204): locate_template() #5 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/single-default.php(16): get_template_part() #6 /www/wwwroot/yxjdzl.com/wp-includes/template.php(772): require('...') #7 /www/wwwroot/yxjdzl.com/wp-includes/template.php(716): load_template() #8 /www/wwwroot/yxjdzl.com/wp-includes/general-template.php(204): locate_template() #9 /www/wwwroot/yxjdzl.com/wp-content/themes/begin/single.php(6): get_template_part() #10 /www/wwwroot/yxjdzl.com/wp-includes/template-loader.php(106): include('...') #11 /www/wwwroot/yxjdzl.com/wp-blog-header.php(19): require_once('...') #12 /www/wwwroot/yxjdzl.com/index.php(17): require('...') #13 {main} thrown in /www/wwwroot/yxjdzl.com/wp-content/themes/begin/inc/avatar-cache.php on line 27
WordPress › 错误